We are Sturm, Ruger & Company® Certified to work on your Ruger Mini 14® & 30® Rifles. You will no longer need to send your rifle to Ruger for restricted factory work. We can handle any factory replacement part work you are needing from firing pins to trigger components and more..... *All factory warranty issues will still need to be handled through Ruger® for now. Please keep in mind that we have been at the cutting edge of technology when it comes to the Mini 14® and Mini 30® rifles for many years.
Accuracy Systems Mini 14 & 30 Adjustable Gas Blocks
Torque Specifications for all Gas Block Screws is 40 Inch LBS
Tired of hitting the fellow 3 shooting benches down in the head and him throwing the brass back at you?
Tired of having to change gas bushings only to find you didn't get the right diameter installed and had to start the process all over again?
- The BeneFits Of Our Adjustable gas block Systems are:
- Will allow you to save all the lost brass that is ejected normally 20 to 30 feet by your factory gas system.
- Will save your scope as well as your receiver during the violent impact that happens every time you fire a round and the operating rod whacks the receiver.
- Will actually help your rifle shoot better by reducing the harmonics that are produced when the operating rod comes in contact with your receiver during high speed cycling of the operating Rod.
- Can be adjusted from no cycling at all for you single shot bench shooters to wide open for you high capacity magazine junkies who don't care where there brass ends up. But some where in between is best.
- Installation is as easy!
- We offer the Generation 4 the most advanced of our generations of gas blocks with the precise positive click adjusting knob.
- No adjusting wrench needed.
- The Generation 5 for those who already have a Accu-Strut, Har-Bar, Trueshot Technologies, or the Mo-Rod and wants a adjustable gas block.
- All above are available in the .562", .625" and .750" diameter.
GENERATION 4 ADJUSTABLE GAS BLOCK
"Our Most Advanced Adjustable Gas Block"
4/4/2024 6:58:51 PM Mountain Daylight TimeSubject: Re: Order #20302 Confirmation — Accuracy StoreI got the Gen 4 .625 gas block installed, really easy to do by the way. That thing is absolutely awesome! Even with the suppressor attached you can feel quite a difference in the way the gun handles, the op rod, the way the brass ejects, etc. Before installing your product the gun would eject brass so violently that it would actually dent the casing on the charging handle and throw the brass 20 ft haha. Now it ejects the brass about 6 ft.
Thank you so much, you have a great product there!
Steve Dennison, Owner
- Will not work with the Accu-Strut, Har-Bar or Mo-Rod. Our Generation 5 gas block below will work with Accu-Strut, Har-Bar or Mo-Rod.
- Positive Click no back out adjustment Knob.
- 7075 Alloy For it's weight stronger than steel with no cracked gas blocks for the last 10 years. *Use correct torque settings.
- 1/2 the weight of the factory gas block.
- Cools faster than the factory gas block.
- Not a cast part as the factory gas block.
- Hole pattern matches factory gas block Top & Bottom.
- Will fit our Scout mount bolt pattern.
- Will fit Amega Ranges, AltiMAK Scout Mount & Ranch Products Scout Mount
- Comes complete with Adjusting knob, Gas pipe, Top & Bottom of gas block, Sling Swivel stud, & 4 screws. (You use your gas bushing)
- Testimonial: attention: Carl, I received the new Gen 4 gas block I ordered over the phone from you and must say I love it. I'm still tinkering with the settings but its nice to be able to turn it into a instant bolt action when the brass snatchers are around the range and leave my reloading brass on my table instead of thirty feet away! Thanks again Steve Tucker cmonster6@hotmail.com 6/19/2013
